Susan Ryanand Siraj Perera
This paper describes the benefits of the statewide risk reporting framework used in dam safety regulation in Victoria and its ongoing development. Key to this approach is a web-hosted reporting system and benchmarking process, established by the Department of Sustainability and Environment in collaboration with the Victorian water industry. This is the first time that such an approach has been used in Australia for publicly owned dams.
Sector-wide reporting on dam safety is central to the objective-based approach used by the Department in the governance and regulation of the water industry. Water corporations submit detailed annual reports on dam safety status. This incorporates ‘self assessment’ against performance criteria based on ANCOLD risk and dam safety management guidelines. These are collated to produce a statewide report of industry-wide results on the progress of dam safety management programs. This benchmarking process is providing a driver for on-going improvement and proving to be an effective tool for regulation of publicly owned dams.
The reporting framework has significantly advanced the understanding of dam safety risk across the water sector, with outputs easily understood by both dam safety practitioners and decision makers. It has improved monitoring and trend analysis of risk management practices, and is informing policy development on demonstration of the ALARP principle and decision-making about appropriate long-term dam safety levels.
Now showing 1-12 of 45 2975:
Dan Forster, Murray Gillon
A robust and defensible dam surveillance process is considered to be the ‘front-line of defence’ in ensuring dams do not present an unacceptable risk to people, property and the environment. The concept of a ‘Quality Chain of Dam Surveillance’ describes the surveillance process as a multi-linked chain where each step in the process forms a critical link. Without rigorous attention given to quality assurance links in the chain can become tenuous or broken and thus compromise the integrity of the whole chain. Hydro Tasmania is currently re-engineering its existing surveillance process using the Quality Chain of Dam Surveillance as a basis.
This paper presents the concept of the quality chain and uses the Hydro Tasmania improvement initiative as an example application of the concept. The paper is intended to provide a fresh perspective on what is sometimes considered a stale topic and reinforces the need for a considered approach to dam surveillance.
2011 – The Quality Chain of Dam Surveillance
Craig Messer, Francisco Lopez, and Manoj Laxman
The Enlarged Cotter Dam is a new 80m high Roller Compacted Concrete Dam being constructed to augment the water supply for the Canberra region. Due to the size of the main dam and the extreme climatic variations in the ACT, where temperatures range from sub zero in winter to in excess of forty degrees in summer, it is expected that significant stresses will be generated during the cooling of the structure. For this reason it is essential that an understanding of the magnitude of these stresses is developed through the initial strength development period and at critical periods such as the first and second winter when the temperature differential between ambient conditions and the core of the structure may be greatest. The development of thermal stress within the structure has critical impacts on both the RCC mix design and the dam construction equipment and methodology.
For the Enlarged Cotter Dam, thermal stresses were investigated using both two and three dimensional finite element transient heat transfer analyses, making use of the thermal properties derived from laboratory testing including instrumented thermal blocks, as well as established literature. Modelling of the thermal stresses in the dam required the development of time dependent concrete properties, such as strength, stiffness and heat generation, with the latter based on test results and calibrated to actual measured values. Additionally, site dependent conditions for ambient temperature, external conduction, convection and radiation factors, dam foundation temperatures and restraint, dam construction sequence, formwork, joint spacing, insulation and timing of reservoir filling were also modelled.
Initial thermal modelling of the dam demonstrated that significant tensile stresses and potential cracking could develop within the structure, at both early and mature concrete ages. Subsequent analyses were developed to investigate methods of reducing these stresses to within acceptable limits. This paper presents the results of the thermal analyses, including the methods to be employed during and after construction to minimise cracking without impacting construction costs and even optimising the speed of construction.
Finite Element Transient Thermal Analysis of the Enlarged Cotter Dam
Monique de Moel, Mark Arnold, Gamini Adikari
Monbulk Saddle Dam, built in 1929, is one of two saddle dams located at the southern end of Silvan Reservoir, near the township of Monbulk, Victoria. The saddle dam is a 5.3m high earthfill embankment with a 230mm wide, centrally located, concrete core wall. The reservoir retained is located in the valley of Stonyford Creek, and impounds approximately 40,500 ML of water at FSL.
Excessive seepage at the right abutment of Monbulk Saddle Dam has been an issue since the early 1970’s. The reservoir has been operating with a level restriction since then to reduce the seepage flows. However; this restriction limits the operational flexibility of the storage. Early investigations concluded that the most likely mechanism for these excessive seepage flows was a defect in the concrete core wall.
Melbourne Water Corporation, (the owner and the operator of the reservoir), undertook a risk assessment for Silvan Reservoir as part of a review of its dams asset portfolio. Based on the information then available, the risk assessment was undertaken using the criteria and guidelines developed by ANCOLD. The result was that the piping risks associated with the seepage from the west abutment at Monbulk Saddle Dam was unacceptable. The risk assessment Panel also cast doubt on the likelihood of the seepage being caused by a defect in the concrete core wall. Melbourne Water therefore engaged SMEC Australia to investigate the likely causes and mechanisms for this seepage and to develop suitable remedial measures for the dam.
The investigations have included a desktop review of historical information, test pit investigations, Sonic borehole drilling, dynamic cone penetration tests, an infrared thermal imaging investigation and an electromagnetic groundwater seepage flow mapping investigation.
These investigations have shown that the most likely cause of the seepage is the presence of permeable foundation layers located beneath and around the existing core wall as the core wall does not extend over the full length of the embankment and becomes shallower towards the abutments.
To satisfy the ALARP principle; risk reduction remedial works Concept Designs are being developed and reviewed.
2011 – Investigating the Piping Risk Associated with Seepage at Monbulk Saddle Dam of Silvan Reservoir, Victoria
Amanda Ament, Jon Williams, Malcolm Barker
Aplins Weir is located on the Ross River in Townsville, downstream from the Ross River Dam. Previous work had identified Aplins Weir as exhibiting factors of safety below 1.0 under normal operating conditions, with over 1000 persons at risk today in the event of failure. Originally constructed in the early 1920s, Aplins Weir has been upgraded and repaired following various failures on a number of occasions. The end result is a complex reinforced concrete and steel sheet pile composite structure reliant for stability on a number of unreliable components. This paper presents the historical data describing the current configuration of the weir, and the analyses required to evaluate the extisting structure, leading to the design of the proposed upgrade works. The final design involves a retrofit of large diameter cast-in-place lined piles and a heavily reinforced base overlay slab designed to completely bypass all existing vulnerable substructure elements.
2011 – Where is our Weir going – an Unusual Upgrade!
T. Mortimer, J. McNicol, P. Keefer, W. Ludlow
CS Energy’s Kogan Creek Coal Mine located in the Surat Basin in Queensland, services the 750MW coal fired, Kogan Creek Power Station. Strip mining generates large volumes of mine waste which is typically used to construct waste dumps. Recent work at the mine has focused on using mine waste to construct an ash storage facility to store ash that is piped over 5 km from the power station as a dense phase slurry. The use of mine waste to construct the ash storage facility provides significant cost and time savings, however a range of design, construction and operation issues needed to be addressed to operate a facility of this type.
This paper describes some of the key design, construction and operation considerations for the ash storage facility. Design considerations include pipeline transport through environmentally sensitive areas, addressing the stability of the embankment and the use of a partial LLDPE geomembrane lining system to reduce the risk of seepage from the storage. Construction considerations include post construction (pre ash deposition) floor treatment to reduce potential settlement. Operational considerations include ash slurry deposition, water management of the decant pond and progressive rehabilitation of the final landform.
2011 – Design, Construction and Operation of a Partially Lined, Ash Storage Facility Constructed from Mine Waste