Jiri Herza and John Phillips
The design of dams for mining projects requires processes and technology that are unfamiliar to many mine owners and managers. Dam designers rely on ANCOLD assessments of Consequence Category, commonly leading to a High rating for mining dams due to a combination of potential loss of life, impact on environment and damage to assets such as mine voids, process plants, workshops, offices, roads, railways etc.
From this High Consequence Category the relevant annual exceedance probabilities for design parameters and loading conditions such as earthquakes and floods are selected.
Mining companies have sophisticated methods available for assessing risk, yet for their assets they often adopt an order of magnitude lower security for earthquake and floods even though the consequences in terms of lives at risk and impact on project are similar.
The discrepancies in the design standards lead to situations where extreme dam loads are adopted to prevent damage and loss of life in assets that theoretically would have already collapsed under much lower loads.
One difference may be that some mining dams exist in an environment which is controlled by a single entity. Unlike other dams, failure of these mining dams would therefore impact only individuals and assets which fall under the responsibility of the same entity.
This paper discusses the discrepancies between the design of mining dams and the design of other mine infrastructure. The paper considers the impact of discrepancies on the overall risk to the mine and compares the degree of protection offered by a factor of safety and the influence of reliability of design input parameters, alternate load paths and design redundancy.
Keywords: Dams, tailings dams, mining, acceptable risk, factors of safety
Now showing 1-12 of 42 2979:
Kim Robinson, Andrew Pattle and Thomas Shurvell
Rowallan Dam is a 43m high clay core rock fill dam located in Northern Tasmania. The dam impounds 121GL used for hydro power generation and has a High A consequence category.
Over the summer of 2014/15 major reconstruction works were carried out on the dam to repair a piping incident from 1968. The work entailed reconstructing two sections of the dam down to foundation level and the upper 7m of the 568m dam crest. During the work, the dam was temporarily exposed to a significantly increased flood overtopping risk.
A range of measures were taken to manage the overtopping risk; such as increasing the dewatering capacity of the dam, lake draw down, installation of a sheetpile wall, development of emergency backfill procedures and a flood forecasting system.
The focus of this paper is on the flood forecasting system and how this was integrated into the overall management of overtopping risk during construction. The forecast models were run automatically on a 2 hour schedule using the latest BoM forecast, telemetered lake levels and rainfall from 7 gauges surrounding the catchment. The system provided a continuous 7 day lake level forecast which guided the site team on when to release water to manage the storage.
In the event that the lake level forecast reached a predetermined trigger level, the dam safety team would have been automatically notified and various emergency procedures would have been triggered in response to the flood warning.
This paper discusses the measures that were taken to manage the flood risk, how it worked in practice and conclusions which are applicable more generally to managing overtopping risk during dam works.
Keywords: dam construction flood risk, flood forecasting
Vicki-Ann Dimas, Wayne Peck, Gary Gibson and Russell Cuthbertson
Globally, reservoir triggered seismicity (RTS) is a phenomenon sometimes observed in newly constructed large dams worldwide, for over 50 years now. Over 95 sites have been identified to have caused RTS by the infilling of water reservoirs upon completion of their constructions worldwide. In Australia, there are seven confirmed sites with observed RTS phenomenon that are summarized by temporal and spatial means.
With almost 40 years of seismic monitoring, primarily within eastern Australia, several of Australia’s largest dams have monitored and recorded many RTS events. At present, twelve dams are 100 metres and above in height as possible candidates, with seven of these actually causing RTS and a disputed possible eighth dam.
Important factors of RTS are reservoir characteristics (depth of the water column and reservoir volume), geological and tectonic features (how active nearby faults are and how close to the next cycle of stress release they are temporally) and ground water pore pressure (decrease in pore volume under compaction of weight of reservoir and diffusion of reservoir water through porous rock beneath). RTS is an adjustment process often delayed for several years after infilling of reservoir before eventually subsiding within 10 to 30 years, when seismic activity then returns to its prior state of stress.
Generally there are two type of RTS events, either a major fault near the reservoir most likely leading to an earthquake exceeding magnitude 5.0 to 6.0, or more commonly, a series of small shallow earthquakes.
Seismic monitoring of all dams (except for Ord River) are presented with spatial and temporal series of maps and cross sections, showing the largest earthquake, build-up and decay of RTS events.
Keywords: Seismic monitoring, reservoir triggered seismicity (RTS), earthquake cycle
Maree Dalakis, Dr Saman de Silva, Siraj Perera and Dr Gamini Adikari
This paper describes the results of a statistical and qualitative analysis on historical dam safety incidents in Victoria, the first study of its kind conducted in the State. The study investigates trends arising from qualitative dam safety incident data collected by the Department of Environment, Land, Water and Planning since the year 1996. The reported incidents are categorised based on their severity and statistical trends are identified in relation to the types of incidents common to regulated and unregulated dams, as well as common responses to incidents, including their post-incident operation. The geographical distribution of incidents across the State is also analysed to determine the effects of seismicity on dam safety incident rates. Furthermore, the unique Victorian conditions of sustained drought and subsequent flooding and their impact on incident rates are investigated through the combined analysis of geographical incident distribution and streamflow data. The incident data is further assessed according to the frequency of visual inspection and reporting of the structures in order to gauge the relative influence of these practices, and dam regulation in general, on mitigating incident risk in dams. An understanding of dam safety incident trends and the impact of inspection and reporting practices is increasingly important given the increasing expectation for dam owners to properly operate and maintain their assets with minimal resources and finances.
Keywords: dam, safety, incident, historical, failure.
Monique Eggenhuizen, Eric Lesleighter, Gamini Adikari
St Georges Dam is located on Creswick Creek approximately 2km southeast of the township of Creswick and 135km northwest of Melbourne. The reservoir, located within the Creswick Regional Park and originally constructed to supply water for the Creswick quartz crushing plant in the 1890s, has since been established as a popular recreational storage and is the responsibility of Parks Victoria. The dam is approximately 16m high and located across a relatively steep gully. The embankment consists of earthfill with an upstream face of rock beaching and a grass covered downstream face. The primary and secondary spillways are cut into the right and left abutments respectively.
At the completion of a detailed design review, St Georges Dam was assessed to be within the top three of Parks Victoria’s dams portfolio in regards to Public Safety Risks. The detailed design review assessed that the risk position for the dam plotted within the unacceptable region of the ANCOLD Guidelines for the static, earthquake and flood failure modes. As such, upgrade measures were considered to be required. In 2010 and 2011, a number of significant flood events emphasised the importance of upgrade works at this dam, particularly in regards to upgrading the spillway capacity, and consequently Parks Victoria assigned these works a high priority.
SMEC was engaged to design the upgrade works for the dam. A number of arrangements to increase the spillway capacity of the dam were considered, with the most cost effective option being assessed to be a secondary spillway over the dam embankment in the form of a rock chute.
This paper describes the decision making process associated with the option selection and the methodology for designing the overbank spillway which utilised the findings in ‘Riprap Design for Overtopping Flows (Abt & Johnson, 1991), and US Army Corps of Engineers, Waterways Experiment Station, publications of standard riprap gradations and computer program CHANLPRO.
Keywords: Embankment Dams, Spillway, Rock Chute, Erosion Protection
Nihal Vitharana, Nuno Ferreira
The raising and/or stabilising of existing concrete gravity dams by continuous concrete buttressing is a viable solution and, in some cases, it is the only solution available. There are few medium-large dams in Australia currently under consideration for raising with continuous buttressing.
Two of the major issues to be surmounted are: (a) the existing dam should not be subjected to cracking (particularly on the upstream face) due to heat-hydration effects, and (b) the requirement for the two dam bodies to resist the hydrostatic and other loadings as a monolith (unified dam).
However, there is great need for understanding the mechanisms involved in selecting an appropriate heat-of-hydration model and in calculating thermal stresses rationally. Due to such lack of understanding, expensive precautions, mostly with compounding conservatisms, would be adopted in concept and detailed designs eg. shear-keys on the interface, artificial cooling, post-grouted interface, anchor bars at the interface, concrete with high cement contents. On the other hand, unsafe designs could be the result.
The paper discusses these issues highlighting that a rational approach can be adopted to economise the design and construction processes. An example is also presented to demonstrate how the potential for temperature-induced cracking in new and old dam bodies can be evaluated with reduced uncertainty by considering all the mechanisms involved in a holistic way.
Keywords: Heat-of-Hydration modelling, raising concrete dams, thermal stresses, concrete buttressing