David Ryan, Peter Richardson, William Steen
Ibis Creek Dam, a referable dam and classified as a mass concrete gravity structure, was constructed in 1906 to supply water for both tin ore processing and the local township of Irvinebank. Irvinebank is a small township near Atherton in North Queensland and is situated about 3 km downstream of the dam. The mill ceased operation in 1990 but the township of Irvinebank remains reliant on the dam for water supply.
In 1996 the dam was raised about 1 m and strengthened by the addition of mass concrete on the crest and downstream face.
One recommendation of the Safety Review conducted in 2009 was that an investigation be made of the strength of the lift joints and the shear capacity of the connection between the Stage I and Stage II concrete sections. The investigations revealed that the structure was not constructed as had been originally assumed and the overall stability of the structure had been overestimated.
This paper details the investigations and remedial works proposed to strengthen the structure so that it complies with current design standards.
Monique de Moel, A/Professor Jayantha Kodikara, Dr Gamini Adikari
All embankment dams have some seepage as the impounded water seeks paths of least resistance through the dam and its foundation. Seepage must, however, be controlled to prevent internal erosion of the embankment or foundation and avoid damage to surrounding structures. Embankment dams are designed to operate under controlled steady state seepage, which over time may change due to movement in the foundation and the dam, chemical actions and other forms of deterioration. Effective monitoring of seepage within embankment dams is therefore essential in regards to management of dam safety and prevention of failure.
Traditional methods of seepage monitoring have involved measurement or visual monitoring on the downstream side of the dam after the seepage has occurred. Effective, early detection of seepage in embankment dams has been difficult as it originates and develops in the subsurface. Infrared Thermal Imaging is such a technique that is non-contact, non-intrusive, simple and flexible. The analysis draws on the temperature behaviour and the heat capacity of materials within the body of the dam and consequently allows the user to identify and isolate temperature variations along the surface of interest. This paper describes the method, application and feasibility of infrared thermal imaging for the detection of seepage in earth and rockfill embankment dams. The value of this technique as an additional tool in the surveillance of dams is discussed.
Infrared thermal imaging has been in use in other fields of engineering for condition monitoring and defect detection of structures. It has shown great potential in identifying variations in surface characteristics, which may not be evident through visual inspection alone. In this paper, reliability of this technique for seepage detection in embankment dams has been analysed using 8 case studies in order to arrive at a fair understanding of the best conditions under which Infrared Thermal Imaging field inspections should be carried out. The results of field investigations undertaken at these dams suggest that Infrared Thermal Imaging is a useful and effective tool for detection of seepage and an aid in identifying seepage behaviour.
Keywords: Seepage Detection, Infrared Thermal Imaging, Dam Surveillance, Monitoring
Graeme Maher, Richard Herweynen, Martin Mallen-Cooper and Stuart Marshall
Increasing awareness of the environmental impact of dams means that fish passage is emerging as a critical issue for both existing and new dams in Australia.
The fish passage and outlet works for Wyaralong Dam, a new dam currently under construction, required accommodation of large ranges of head and tailwater levels. The solution that has been adopted, a bi‐directional fishlift using a single hopper with trapping for downstream fish movement occurring within the intake tower, is a world first. The solution required the innovative integration of a number of existing technologies to create a system which is necessarily complex, yet reliable and effective.
The paper incorporates discussion of the critical design constraints, the biology of fish passage, the process adopted to reach the concept solution and a description of the final design including its integration with the outlet works. A number of design issues and their solution are discussed in detail, particularly those associated with dealing with the complexity of the design constraints and how the components of the solution were integrated into a seamless design.
The paper will be of use to those involved in the process of providing fish passage on both existing and new structures that obstruct river flow.
A Bi-Directional Fishlift – An Innovative Solution for Fish Passage
An essential criterion for any new dam project in Australia is to provide for passage of fish past the structure in both the upstream and downstream direction. In recent projects with a relatively high barrier this has been provided by mechanised systems such as locks, lifts or a combination of both.
A nature-like fishway provides for passage of fish past a barrier by applying some of the features of natural streams. The concept has been increasingly applied to fishway designs in North America and Europe. A nature-like fishway will provide variable flow depths, velocities and turbulence across its width and along its length and is constructed using natural materials to simulate the natural stream characteristics. The variable flow conditions coupled with the use of natural materials inherently result in different channel substrates that support the passage of a large range and size of fish species as well as other aquatic species. Where fish habitat has been depleted, a nature-like fishway can also supplement and enhance aquatic habitat.
The performance of nature-like fishways can be difficult to quantify due the very nature of the system. However, qualitative assessments in North America are indicating that a wide range of species are using such fishways and that fish species that were previously extirpated from rivers are again migrating.
The nature-like fishway concept has been applied to in-stream structures up to four metres high in the eastern states of Australia. However, the substantial progress made with this design in North America and Europe has not as yet been applied in this country.
This paper analyses the advantages and disadvantages of nature-like fishways over mechanised systems, such as locks and lifts, and makes an assessment of the suitability of the concept to dams in Australia with relatively high walls.
Richard Herweynen, Colleen Stratford
Assessing the potential for erosion of foundation rock downstream of a spillway is a problem faced on many dams, whether new or existing. The problem is made particularly difficult not only due to the uncertainty in determining the erosion potential of the rock, but also due to the variable hydrologic characteristics of flood events.
The selected spillway option for Wyaralong Dam comprises a centrally located primary spillway with a secondary spillway located on the left abutment. A stilling basin energy dissipater is provided at the toe of the primary spillway. Downstream of the secondary spillway, an apron channel will direct flows back to the stilling basin. However, for flood events larger than the 1 in 2000 AEP event, the capacity of the secondary spillway apron is exceeded and flows spill out across the left abutment of the dam towards the river channel. Erosion of this left abutment was viewed to be a potential dam safety issue, and as such, careful consideration was required during the design stage to determine the acceptability of this spillway arrangement.
In order to provide structure to a problem which often relies solely on engineering judgment, a decision process was developed, taking into consideration some of the more definable aspects of the problem. These aspects included the geological characteristics, the initial hydraulic characteristics, the flood duration, the nature of erosion should it occur and the stability of the dam. This paper describes the decision process and methodology used at Wyaralong Dam to
determine the acceptability of erosion. This paper will present the process in a way that it can be used by others in future dam projects, both new and upgrades.
A Unique and Holistic Approach to the Erodibility Assessment of Dam Foundations
Richard Herweynen, Robert Montalvo, John Ager
The choice of materials used in the construction of a dam is one of the most critical decisions in the design process. Our natural behaviour as engineers is to adopt materials which have proven performance, and which conform to Australian or international standards, which sometimes causes us to overlook the specific conditions and demands of the project at hand. In an environment where the majority of concrete produced is for structural purposes, the properties of these concretes is often vastly different to those desired for mass concrete structures such as dams and spillways.
The big question at Wyaralong Dam was could onsite aggregate be used in the Roller Compacted Concrete (RCC)? The Wyaralong Dam is located in the Gatton Sandstone (early Jurassic), predominantly feldspathic to lithic‐feldspathic sandstones with a clay matrix. Early analyses and tests suggested that the Gatton Sandstone was not suitable for RCC aggregate due to a 68% wet/dry strength reduction, high water absorption (5.2 – 7.5%) and petrographic interpretation that clay content was mainly swelling clay, leading to durability concerns.
Due to significant community, safety and cost issues with importing aggregate, Wyaralong Dam Alliance (WDA), during the development of the RCC mix design for Wyaralong Dam, chose to pursue the use of onsite quarried sandstone aggregate instead of importing aggregate. Additional petrographic and XRD analyses and extensive durability tests were undertaken on cores of sandstone and RCC samples, including wet‐dry cycles, soak tests in ethylene glycol, soaks in sodium hydroxide, and heating and cooling cycles. These tests indicated that, if swelling clays are present, they do not impact the durability behavior of the RCC aggregate.
The substantial effort put into testing the sandstone aggregate has paid off for WDA. Not only have the results indicated that the RCC mix performs remarkably well in terms of durability, but the very low modulus of elasticity of the mix has provided exceptional performance in terms of thermal loading; with all the related benefits in reduced restrictions to placement schedule and cooling requirements. Onsite sandstone was not only proven to be a feasible option, it has been demonstrated that it is the best option for the project. Details of the study are provided in this paper.
Keywords: Roller Compacted Concrete (RCC), Sandstone, Aggregate, Clay, Mix, Durability