In Austria, special procedures for ensuring dam safety apply to dams higher than 15 m or reservoirs with a capacity of more than 500,000 m³. There are at present about 90 dams which belong to this category. The largest one is the 200 m high Kölnbrein arch dam.
In general, it is the task of the dam owner to provide for the safety of a dam. For that, he has to appoint qualified engineers, the “Dam Safety Engineers”, which are in charge of dam surveillance and maintenance. The Water Authority verifies that the owner makes the necessary provisions for dam safety. Water Authorities are the Provincial Governor and the Federal Minister of Agriculture and Forestry. The Water Authorities are supported by a governmental advisory board, the “Austrian Commission on Dams”.
Projects for new dams or for reconstruction of existing dams are examined by the Austrian Commission on Dams. Approval by the Water Authority is based on the findings of this commission. A group of a few experts of the commission accompanies the project during construction, first impounding and the final acceptance procedure. In normal operation, dam attendants carry out visual inspections and measurements. The most important instruments are measured automatically and the data are transmitted to a permanently manned control centre. The Dam Safety Engineer has to inspect the dam at least once a year. His annual report to the Water Authorities must contain an assessment of the safety of the dam. The Federal Dam Supervisory Department of the ministry checks the annual reports and carries out an in-depth inspection of the dam at least every five years.
In the case of extraordinary events, the Dam Safety Engineer has to assess the situation and he has to set appropriate measures. An Emergency Action Plan is available for all dams of the said category.
— OR —
Now showing 1-12 of 59 2970:
Nerida Bartlett, David Scriven, Peter Richardson
The failure of a number of consecutive wet seasons has resulted in storage levels in Eungella Dam being at dangerously low levels such that supply could be exhausted by June 2007. Eungella Dam supplies bulk water to the Bowen Basin coal fields as well as the Collinsville power station and the Collinsville township.
The Collinsville township, power station and coal mine as well as the Newlands mines take water from the Bowen River Weir which is supplied from Eungella Dam some 95 kilometres upstream. Transmission losses of the order of 25 to 50% have been experienced for releases from Eungella Dam to Bowen River Weir.
The Eungella Dam catchment area is 142 square kilometres. Significant flows occur in the Bowen River downstream of Eungella Dam, the catchment area above Bowen River Weir being 4,520 square kilometres. The topography in the surrounding area (near Collinsville) is not suitable for dam construction.
The opportunity existed for the construction of an offstream storage adjacent to the Bowen River Weir so that the downstream flows could be captured reducing the demand on Eungella Dam thus making more water available for upstream users.
A 5,200 ML offstream storage, associated pump station and rising main was designed, constructed and filled within a period of 12 months.
Foundations at the site are highly permeable sands. Marginally suitable clay for a seal was in short supply as was suitable rock for slope protection. A fixed price budget had been set by the contributing customers.
This paper describes the hydrology, site conditions, design and construction of the project.
The Koralpe hydropower scheme is a major development on the Feistritzbach tributary of the River Drau to utilize water in a 50 MW powerhouse located in the south-eastern Carinthia, Europe. The Soboth reservoir is situated 735 m higher in a narrow valley and is created by the 85 m high Feistritzbach dam which was constructed near the border of Austria and Slovenia between 1988 and 1990. This rockfill dam is the latest addition to KELAG’s more than 15 structures and is sealed by an asphaltic core. The excellent deformability and impermeability of the asphaltic core is able to follow the deformation of the compacted rock-fill material best during construction, initial filling and operation period without any seepage. The asphaltic core was placed in three 20 cm layers per day by a specially developed placing unit from a contractor. The upstream and downstream filter zone was placed at the same time with the same machine and compacted carefully by vibrating rollers. The dam is curved in plan with a radius of 650 m and contains about 1.6 million m³ rock fill material. The surface of the downstream side was built exceeding the environmental standards of the time.The most important indicator of the normal function of a dam is the behaviour of seepage. A monitoring system of seepage, piezometers, earth pressure cells and deformation has been installed. The seepage water is monitored online at seven points of the dam base and at the access tunnel to the bottom outlet valve. Geodetic measurements on and inside the dam are done once a year. Several additional pieces of surveillance equipment were installed to observe the behaviour of the asphaltic core. The paper concentrates on the design, construction and performance of the dam with the asphaltic core.
The Water Act 2003 established a new role for the Environment Agency, that of the Enforcement Authority for the Reservoirs Act 1975 in England and Wales. The transfer of this regulatory role from 136 Local Authorities has had a significant impact on the regulated community. Further change is heralded with the forthcoming introduction of Reservoir Flood Plans, Post-Incident Reporting and a review of current regulations. The improvements sought in reservoir safety may be at risk due to a growing skills shortage and increasing financial constraints imposed by owners.
This paper highlights the issues impacting on the reservoir industry in England and Wales and in recognising developments made by ANCOLD members the author seeks to understand how they are being responded to in Australia.
Karen Riddette, David Ho & Julie Edwards
Over the last five years in Australia, the use of computational fluid dynamics for the investigation of waterflows through hydraulic structures has been steadily rising. This modelling technique has been successfully applied to a range of dam upgrade projects, helping to assess spillway discharge capacity and structural integrity, and giving insight into flow behaviours including orifice flow, shock wave formation and chute overtopping (Ho et al, 2006). Innovative and cost effective upgrade solutions have been implemented from numerical model studies including baffle plates (Maher and Rodd, 2005) and locking arrangements to protect radial gates from extreme floods.
This paper will begin with a review of recent dam engineering applications, including outlet flow through a fish screen, the performance of a fishway against hydraulic and environmental criteria and pipe flow in a large pumping station. Some of the difficulties and limitations of the modelling technique will be examined together with current research being conducted to address these issues and further validate the numerical results against published data. Some interesting results to date will be reported on elliptical crest discharge, boundary geometry, and model/prototype correlation.
With increasing computing power and software enhancements, the potential applications for numerical simulation in dam engineering continue to grow. This paper will also examine the future outlook and highlight some recent advances such as the thermal simulation of cold water pollution, air entraining flows and combined free-surface and pipe flow in a morning glory spillway.
R. Dawson, J. Grimston, R. Cole, D. Bouma
The authors have been involved in the design and construction of several embankment dams in New Zealand over the past decade, and have considerable corporate knowledge from dams designed by the company in its 47-year history. This paper examines four dams which are relatively small to medium, ranging in height from 10 to 19 m with moderate storage volumes. Three of the dams service landfills and the fourth a wood processing mill. Such dams may provide the designer with considerable challenges due to their relatively low capital cost resulting in limited investment in geotechnical investigation at the front end of the project, with varying levels of change often required during construction due to unforeseen conditions as a result of the limited investigations.
The general arrangement and conceptual design principles for each of the dams is described followed by the field investigation and laboratory testing undertaken for each dam, together with the interpreted ground conditions.
The experiences from construction have helped to develop techniques for a balance between preliminary design, investigation, and evolution of the design and specification during construction. It is imperative to develop a sufficiently detailed preliminary design, on the basis of readily available information such as visual and geological assessment, to allow the investigation to be thoughtfully designed to allow the major assumptions to be verified. This needs to be followed by a skilfully executed geotechnical investigation with the designer advising on findings and changing direction as necessary through the investigation. An investigation trench along the full alignment of the cutoff trench (if envisaged in the design) is warranted. Earthworks specifications should be evolved early in the construction phase through compaction trials using specific plant for the site, and backed up by insitu and laboratory testing.