Hydro Tasmania uses an electronic inclinometer to monitor the face deflections of nine of its CFRDs. The inclinometer is lowered down a steel pipe attached to the upstream face of each dam. The inclinometer was designed and constructed by the University of Tasmania and was first used on Cethana Dam when it was completed in 1972.
The success of its use on Cethana Dam lead to its use for the long term monitoring of eight subsequent CFRDs constructed by Hydro Tasmania.
After 25 years of successful operation some irregular readings of face deflection became apparent. This paper describes the investigation of the irregular readings that had been obtained, the assessment of other methods of observing concrete face deflection, and the refurbishment of the inclinometer using modern electronic components.
Now showing 1-12 of 72 2967:
The Bureau of Meteorology has recently revised the Probable Maximum Precipitation (PMP) estimates for the Generalised Tropical Storm Method (GTSM) region of Australia. The revision process has involved the application of the more technically rigorous Generalised Southeast Australia Method (GSAM) that was previously developed for the southern part of Australia to a much larger data set of severe tropical storms. This has generally lead to an increase in the total GTSM PMP depths with a resultant increase in the Probable Maximum Precipitation Design Flood (PMPDF) and the Probable Maximum Flood (PMF).
In addition, the revision process has produced significant modifications to the temporal and spatial patterns adopted when applying the PMP depths to a dam’s catchment and these changes have also generally lead to increases in the resultant floods.
This paper discusses the rationale behind the increases in PMP depths and changes in the associated temporal and spatial patterns and presents the justification for the adoption of these more scientifically defensible estimates.
The application of the revised PMP estimates to the Keepit Dam catchment in northern NSW is presented and a comparison between the PMPDF and PMF estimates based on the original GTSM and the revised GTSM (GTSMR) made for this specific case study.
Peter D Amos, Thomas G Newson, Murray D Gillon
In September 2000, pressures being monitored in a geological fracture beneath Arapuni Dam were found to be rising significantly, indicating that a deteriorating condition was developing in the foundation. Two boreholes drilled in 1995 had intersected high water pressures within the fracture in an area close to the downstream face of the dam, posing a risk of major leakage developing from where the fracture day-lighted downstream of the dam. Lumps of clay, bitumen and lake biota, including snails and small fish, were identified discharging from the boreholes, indicating that a significant leakage path had developed. Detailed investigations, the subject of this paper, were carried out from September 2000 to confirm the extent and nature of the deterioration. A range of groundwater investigation techniques and tools were used, while the reservoir remained full, to identify the source of the leak and confirm the path it took. The investigations culminated in development of a groundwater model that described the seepage behaviour in the dam foundation. Based on the investigation information gathered, the foundation fracture bearing the high water pressure was successfully grouted in December 2001 without lowering the reservoir.
Suzie Gaynor, Jocelyn Potts, David Watson
State Water # as manager of Keepit Dam has established a comprehensive upgrade project.
A portfolio risk assessment by State Water of its major dams placed Keepit Dam as the highest priority for an upgrade.
While extreme flood and earthquake dam safety are the main drivesr for this upgrade, the opportunity has been taken to integrate other key dam management considerations into the process including environmental improvements, flood mitigation and sustainable regional development.
The dam, which is located on the Namoi River some 45km upstream of Gunnedah, is, in tandem with Split Rock Dam upstream, a vital irrigation water supply for the Namoi Valley region in northern New South Wales.
In considering the most appropriate way of addressing the critical flood safety issue, it became very apparent that the solutions were many and they significantly impacted on the local community. Other important issues such as water quality and flood mitigation, and overall sustainable development in the valley, particularly system water reliability, could influence dam safety solutions and so also needed to be considered as part of the process. As such it was considered imperative that the local community be actively involved in determining both interim and long-term upgrade solutions.
To achieve the best outcome for the region, State Water since mid 2001, has used the community consultation approach to guide the project.
Currently interim works have been completed and long-term options are being evaluated.
An Environmental Impact Statement on the preferred proposal will be undertaken during the later part of 2004 and if approved, all works will be completed by end of 2007.
This paper will highlight our experiences to date including:
Bill Hakin, Peter Buchanan, Doug Connors, Darren Loidl
To allow greater flexibility in their generation and hence a better response to the peaks in electricity demand, Southern Hydro decided to increase the Full Supply Level of Dartmouth Regulatory Dam by 3.5m using labyrinth Fusegates.
The Regulating Dam is located on the Mitta Mitta River, approximately 8 km downstream of Dartmouth Dam. It is a 23 m high concrete gravity structure with a 60 m long central spillway section. The dam forms the storage required for regulating releases from the Dartmouth Power Station back to the Mitta Mitta River, so as to satisfy environmental requirements.
Although this is the second Fusegate project in Australia it is unique in that difficult access conditions determined that construction in mild steel would be the most appropriate. Initial civil works involved construction of a flat sill to replace the Ogee spillway crest so that it could support the Fusegates. The installation contractor devised an ingenious method for installing the huge structures over the top of the gate-house which blocks direct access to the spillway. Design was very much undertaken with the installation method in mind to ensure a high quality project with minimum contractual risk.
This paper discusses the construction stage of this very interesting spillway modification.
Richard Olive John Wonnacott, Stefan Schwank
The Diavik Dyke was constructed in 2001/2 in a major sub-Arctic lake in Canada’s Northwest Territories, to permit an open-pit diamond mining operation. The dyke, 3.9km long, was built in water up to 20 metres deep in a period of 17 months. For ten months of this period the lake was frozen. The project was notable for the extreme climate, discontinuous permafrost in the dyke foundations, very difficult logistics and the exceptional environmental constraints.
Project economics dictated a short construction period to permit the early generation of revenue from the mine. To confidently deliver a secure dyke within the time frame, the world’s most technologically advanced cut-off wall equipment was designed and fabricated in Germany.
This paper provides an overview of the dyke and focuses in more detail on the specialty equipment used for the cut-off wall and foundation treatment.