John Grimston, Robin Dawson, Maurice Fraser
Water supply for irrigation of horticulture and agriculture in New Zealand has gained considerable momentum since the mid 1990’s. The rapid growth of the wine industry in areas such as Marlborough (located at the top of the South Island) and dairy conversions in many areas of South Canterbury are prime examples of the pressure being applied to existing water supplies and sources and the increasing need for new irrigation supplies and security of supply.
The larger irrigation projects of the past were implemented by the government – schemes such as the Rangitata Diversion race and the Lower Waitaki irrigation project both on the east coast of the South Island. The 1990’s and early 2000’s has seen a largely hands off government approach to potential irrigation projects with the shift towards leaving it to market forces to build irrigation schemes. The result has been that due to significant larger project risks and capital cost requirements with often multi party stakeholder groups, only relatively small schemes have been implemented – the Waimakariri irrigation scheme and Opuha irrigation dam are a few examples. However, in recent years with the value of water increasing several significant irrigation projects promoted by private enterprise or progressive district councils with farmer groups are being investigated and a few may be close to implementation.
The recent drought conditions have focussed attention on the need for storages to maintain security of supply and, together with the balance with sustainability, the consenting environment in New Zealand and existing river/aquifer allocations, significant challenges to development are presented.
Specific case examples include the proposed Delta dam near Blenheim being developed by a private group of irrigators and the Bankhouse development being implemented by a private owner in the same Marlborough region.
This paper provides a background to irrigation in the South Island and describes these two proposed schemes and associated storage dams, together with an insight into the key issues related to the proposed projects.
The Diavik Dyke was constructed in 2001/2 in a major sub-Arctic lake in Canada’s Northwest Territories, to permit an open-pit diamond mining operation. The dyke, 3.9km long, was built in water up to 20 metres deep in a period of 17 months. For ten months of this period the lake was frozen. The project was notable for the extreme climate, discontinuous permafrost in the dyke foundations, very difficult logistics and the exceptional environmental constraints.
Project economics dictated a short construction period to permit the early generation of revenue from the mine. To confidently deliver a secure dyke within the time frame, the world’s most technologically advanced cut-off wall equipment was designed and fabricated in Germany.
This paper provides an overview of the dyke and focuses in more detail on the specialty equipment used for the cut-off wall and foundation treatment.
Richard Olive John Wonnacott, Stefan Schwank
Many dam structures in Australia were designed and built in the 1950s and 60s with limited hydrological information. As a result existing spillway structures are under-sized for today’s revised probable maximum floods (PMF). Potential problems such as the generation of excessive negative pressure over spillway crest under increased flood condition could be encountered. This may cause instability or cavitation damage to the spillway. The raised flow profile may also have adverse impacts on crest bridges and gate structures.
Historically, physical models have been constructed in hydraulic laboratories to study these behaviours, but they are expensive, time-consuming and there are many difficulties associated with scaling effects. Today, with the use of high-performance computers and more efficient computational fluid dynamics (CFD) codes, the behaviour of hydraulic structures can be investigated numerically in reasonable time and expense.
This paper describes the two- and three-dimensional CFD modelling of spillway behaviour under rising flood levels. The results have been validated against published data and good agreement was obtained. The technique has been applied to investigate several spillway structures in Australia.
SEQWater is the major supplier of untreated water in bulk to Local Governments and industry in the South East Queensland region of Australia, through ownership of Wivenhoe, Somerset and North Pine Dams. Wivenhoe Dam (Lake Wivenhoe) is located on the Brisbane River in Esk Shire. The storage provides both flood mitigation and water supply storage to Brisbane and Ipswich. The water supply storage capacity at full supply level is 1,160 GL. An additional 1,450 GL of storage above full supply level is used for flood mitigation.
Changes to the estimation of extreme rainfall events has resulted in significant increases in the estimates of the PMF since the original design of Wivenhoe Dam. To upgrade the flood security of Wivenhoe Dam, SEQWater has formed an alliance with Leighton Contractors, Coffey Geosciences, MWH and the NSW Department of Commerce.
This paper details the alliance delivery method, the latest estimates of the PMF based on the GTSMR method and details of the two preferred options being finalised by the Alliance.
Hydro Tasmania has recently developed a Dam Safety Emergency Plan, which covers 54 referable dams throughout Tasmania. A major contribution was the development of the Pieman River flood warning system. The flood warning system is a computer-based model that forecasts the hydrological situation of the catchment up to 48 hours into the future and alarms the appropriate personnel when a flood event is imminent. The Pieman River catchment experiences some of the highest average annual rainfalls in Tasmania and contains dams in the High Hazard category. The flood warning system was developed using Hydstra Modelling™ (formerly TimeStudio), which links directly to the Hydstra TSM™ database. This package offers powerful automation tools that enable the Pieman River flood warning system to operate, alert personnel and display results on Hydro Tasmania’s internal website with no manual involvement. With its maintenance free operation and user-friendly interfaces, the Pieman River flood warning system is an effective contribution towards the overall risk management package of the Pieman River Power Development.