In 1998, ANCOLD Guidelines entitled “Guidelines for Design of Dams for Earthquake” was issued. The Guideline mainly deals with the seismic aspects of dams and only a basic reference is made to the seismic assessment of intake towers in Section 8.3. Although the much needed and pioneering step taken to introduce this Guideline is to be appreciated and it has covered the seismic aspects of dams, some confusion does exist amongst dam / structural engineers in assessing the seismic performance of concrete intake towers. This is mainly due to the fact the behaviour of reinforced concrete intakes towers is quite different from that of earth or concrete gravity dams. This confusion could potentially lead to gross overestimate of the inertia loads on concrete intake towers resulting in unnecessary expenditure in investigation and remedial works.
The energy dissipation due to inelastic hysteresis behaviour of concrete members results in a great reduction in the inertia loads compared with those calculated with traditional “elastic” analysis methods. This consequently results in significant reductions in bending moments and shear forces on the tower and its foundation. It is very important to understand the basic behaviour of reinforced concrete, considering the composite action of concrete, longitudinal & hoop reinforcing steel, before embarking in sophisticated dynamic analysis the outputs of which are highly dependent on the input parameters
The authors have developed a methodology in which the hysteresis energy dissipation due to the inelastic behaviour of concrete intake towers is considered. Various criteria were defined for serviceability and ultimate failure modes such as excessive deflection, spalling of concrete, buckling of reinforcing steel. The confinement effect of hoop steel on the core concrete is also considered.
This paper will present the fundamental aspects of seismic behaviour of reinforced concrete structures with practical cases as applied to intake towers. The results showed that the current methods adopted by various Dam Authorities in Australia are cursory and the energy dissipation aspect should be considered, in conjunction with expert advice, before undertaking any remedial works.
Phillip Jordan, Rory Nathan, L. Mittiga1 M. Pearse, and Brian Taylor
There are many important dams and other structures on catchments smaller than 1000 km² with response times less than 24 hours, however these catchments have been largely overlooked in previous research into large and extreme floods. This paper is an initial step in “catching up” design practice for short duration rainfall events to the current best practice that is available for estimation of floods from rainfall events with durations of 24 hours and greater.
Two issues are specifically addressed in this paper. Firstly, a regional analysis of short duration rainfall depths is conducted to extend the frequency curve beyond an AEP of 1 in 100. Rainfall frequency curves are estimated for durations between 0.5 and 12 hours, using data from ten pluviograph sites around Australia. Secondly, sets of temporal patterns are derived that could be useful in joint probability analysis of short duration rainfall events. The effects of these new rainfall depths and temporal patterns on flood frequency curves are tested by applying them to rainfall-runoff routing models for three dams with small catchment areas.
David Ho, Karen Boyes, Shane Donohoo and Brian Cooper
Many dam structures in Australia were designed and built in the 1950s and 60s with limited hydrological information. As a result existing spillway structures are under-sized for today’s revised probable maximum floods (PMF). Potential problems such as the generation of excessive negative pressure over spillway crest under increased flood condition could be encountered. This may cause instability or cavitation damage to the spillway. The raised flow profile may also have adverse impacts on crest bridges and gate structures.
Historically, physical models have been constructed in hydraulic laboratories to study these behaviours, but they are expensive, time-consuming and there are many difficulties associated with scaling effects. Today, with the use of high-performance computers and more efficient computational fluid dynamics (CFD) codes, the behaviour of hydraulic structures can be investigated numerically in reasonable time and expense.
This paper describes the two- and three-dimensional CFD modelling of spillway behaviour under rising flood levels. The results have been validated against published data and good agreement was obtained. The technique has been applied to investigate several spillway structures in Australia.
Hydro Tasmania has recently developed a Dam Safety Emergency Plan, which covers 54 referable dams throughout Tasmania. A major contribution was the development of the Pieman River flood warning system. The flood warning system is a computer-based model that forecasts the hydrological situation of the catchment up to 48 hours into the future and alarms the appropriate personnel when a flood event is imminent. The Pieman River catchment experiences some of the highest average annual rainfalls in Tasmania and contains dams in the High Hazard category. The flood warning system was developed using Hydstra Modelling™ (formerly TimeStudio), which links directly to the Hydstra TSM™ database. This package offers powerful automation tools that enable the Pieman River flood warning system to operate, alert personnel and display results on Hydro Tasmania’s internal website with no manual involvement. With its maintenance free operation and user-friendly interfaces, the Pieman River flood warning system is an effective contribution towards the overall risk management package of the Pieman River Power Development.
K. Chandler, D. Gill, B. Maher, S. Macnish and G. Roads
SEQWater is the major supplier of untreated water in bulk to Local Governments and industry in the South East Queensland region of Australia, through ownership of Wivenhoe, Somerset and North Pine Dams. Wivenhoe Dam (Lake Wivenhoe) is located on the Brisbane River in Esk Shire. The storage provides both flood mitigation and water supply storage to Brisbane and Ipswich. The water supply storage capacity at full supply level is 1,160 GL. An additional 1,450 GL of storage above full supply level is used for flood mitigation.
Changes to the estimation of extreme rainfall events has resulted in significant increases in the estimates of the PMF since the original design of Wivenhoe Dam. To upgrade the flood security of Wivenhoe Dam, SEQWater has formed an alliance with Leighton Contractors, Coffey Geosciences, MWH and the NSW Department of Commerce.
This paper details the alliance delivery method, the latest estimates of the PMF based on the GTSMR method and details of the two preferred options being finalised by the Alliance.
Peter D Amos, Thomas G Newson, Murray D Gillon
In September 2000, pressures being monitored in a geological fracture beneath Arapuni Dam were found to be rising significantly, indicating that a deteriorating condition was developing in the foundation. Two boreholes drilled in 1995 had intersected high water pressures within the fracture in an area close to the downstream face of the dam, posing a risk of major leakage developing from where the fracture day-lighted downstream of the dam. Lumps of clay, bitumen and lake biota, including snails and small fish, were identified discharging from the boreholes, indicating that a significant leakage path had developed. Detailed investigations, the subject of this paper, were carried out from September 2000 to confirm the extent and nature of the deterioration. A range of groundwater investigation techniques and tools were used, while the reservoir remained full, to identify the source of the leak and confirm the path it took. The investigations culminated in development of a groundwater model that described the seepage behaviour in the dam foundation. Based on the investigation information gathered, the foundation fracture bearing the high water pressure was successfully grouted in December 2001 without lowering the reservoir.