John Phillips, Yu Sheng, Jennifer Henderson
The main iron ore body at Cockatoo Island in the West Kimberleys forms a cliff face plunging steeply into the sea. It was mined by BHP down to low tide level, but the tidal range of 10 metres hampered operations. Being a very pure and sought after ore, various investigations were made to determine methods of extracting the ore below the sea. A coffer dam into the sea was investigated with the conclusion that the soft marine sediments and apparent artesian groundwater in the foundation posed a major risk and high costs.
The mine was sold to a smaller company who proceeded to win useful ore from the island. They also eyed off the undersea ore and approached GHD to use soft ground technology developed for the Derby Tidal Power Project. The soft marine sediments and apparent artesian groundwater conditions were investigated.
The paper describes the design processes involved to achieve dam stability in a space limited by lease boundaries and the desire to maximise the amount of ore that could be accessed. A key to the process was the development of construction techniques and core placement procedures that could cope with the tidal range. Timing aspects were crucial and were controlled by observations of an extensive array of instruments installed for control purposes.
Now showing 1-12 of 72 2967:
K. Chandler, D. Gill, B. Maher, S. Macnish and G. Roads
SEQWater is the major supplier of untreated water in bulk to Local Governments and industry in the South East Queensland region of Australia, through ownership of Wivenhoe, Somerset and North Pine Dams. Wivenhoe Dam (Lake Wivenhoe) is located on the Brisbane River in Esk Shire. The storage provides both flood mitigation and water supply storage to Brisbane and Ipswich. The water supply storage capacity at full supply level is 1,160 GL. An additional 1,450 GL of storage above full supply level is used for flood mitigation.
Changes to the estimation of extreme rainfall events has resulted in significant increases in the estimates of the PMF since the original design of Wivenhoe Dam. To upgrade the flood security of Wivenhoe Dam, SEQWater has formed an alliance with Leighton Contractors, Coffey Geosciences, MWH and the NSW Department of Commerce.
This paper details the alliance delivery method, the latest estimates of the PMF based on the GTSMR method and details of the two preferred options being finalised by the Alliance.
This paper provides an insight into the management of reservoirs under drought conditions within the new water management frameworks established under the Council of Australian Governments (COAG) Water Reforms. Traditional approaches to the sharing of available supplies during drought are no longer appropriate as the roles of the resource regulator, infrastructure operator, and Government have been separated in the interests of providing certainty for water users and the environment. Recent experiences during drought in the Upper Mary River system near Gympie in Queensland has demonstrated the need to ensure the robustness of water sharing rules for reservoirs under the new framework if certainty is to be delivered.
A. Swindon, T. Griggs, R. Herweyne and R. Fell
Cairn Curran Dam is a 44m high zoned earthfill embankment located near Bendigo in central
Victoria. The dam is owned and operated by Goulburn-Murray Water.
A risk assessment had identified that the junction between the embankment and spillway wall was a
weakness in regard to the potential for piping. Initial geotechnical investigations indicated a softened
zone adjacent to the foundation.
The conceptual upgrade design was to excavate the downstream slope and place filter material and a rockfill weighting berm. A 2-D slope stability analysis gave unacceptably low factors of safety for this excavation. The three dimensional nature of the embankment/spillway interface and excavation
geometry was identified as an important factor in the upgrade design.
A detailed geotechnical assessment was undertaken and a geotechnical model developed that
accounted for potential softened zones adjacent to the spillway wall, along the foundation, and within
A 3-D limit equilibrium slope stability program was utilised to analyse the 3-D factors of safety. The
program employed an extension of Bishop’s method of slices to a 3-D ‘method of columns’. A 3-D
finite element analysis was also undertaken to estimate likely deformations of the embankment and cut slope during construction.
The development of the geotechnical model and subsequent analysis allowed the upgrade works to be undertaken with confidence.
There are many important dams and other structures on catchments smaller than 1000 km² with response times less than 24 hours, however these catchments have been largely overlooked in previous research into large and extreme floods. This paper is an initial step in “catching up” design practice for short duration rainfall events to the current best practice that is available for estimation of floods from rainfall events with durations of 24 hours and greater.
Two issues are specifically addressed in this paper. Firstly, a regional analysis of short duration rainfall depths is conducted to extend the frequency curve beyond an AEP of 1 in 100. Rainfall frequency curves are estimated for durations between 0.5 and 12 hours, using data from ten pluviograph sites around Australia. Secondly, sets of temporal patterns are derived that could be useful in joint probability analysis of short duration rainfall events. The effects of these new rainfall depths and temporal patterns on flood frequency curves are tested by applying them to rainfall-runoff routing models for three dams with small catchment areas.
Garth Barnbaum and Robert Bell
Hydro Tasmania has recently upgraded the control systems for the spillway gates of three of its dams, Clark Dam, Meadowbank Dam and Liapootah Dam. The upgrades followed internal reliability assessments that highlighted high reliance on operator attendance, single points of failure and operational difficulties on each of the three gate systems.
The three gates are of contrasting types. Clark Dam Spillway Gates are submerged orifice type radial gates, operated by wire rope hoists. Meadowbank Crest Gates are flap type gates, held by 10 hydraulic cylinders per gate, a design that has had a difficult operating history. Liapootah is a floating drum gate. The upgrades for each gate therefore required different solutions, albeit within a common basis of design framework. The solutions arrived at are innovative, and meet or exceed worlds best practice.
All three gates are now fully automatic, with PLC control. The use of PLC’s significantly enhances the reliability of the gates. Extensive use is also made of the PLC in monitoring key systems. For example, an impossibly rapid lake level rise detected by one transducer, but not its duplicate, will be alarmed but ignored to avoid unnecessary discharge. All systems incorporate appropriate redundancy. The PLC systems also provide some automatic functional testing functionality and enhance remote alarms and local fault finding.
Mechanical systems were modified to facilitate automation and increase reliability. Stand by power sources used include auto-start diesel genset, DC batteries and a micro hydro generator.
The design and implementation of each of the upgrades was carried out by the Electrical and Mechanical Group of Hydro Tasmania’s Consulting Division, in conjunction with Generation Division’s Project Management Group.