Hydro Tasmania has recently developed a Dam Safety Emergency Plan, which covers 54 referable dams throughout Tasmania. A major contribution was the development of the Pieman River flood warning system. The flood warning system is a computer-based model that forecasts the hydrological situation of the catchment up to 48 hours into the future and alarms the appropriate personnel when a flood event is imminent. The Pieman River catchment experiences some of the highest average annual rainfalls in Tasmania and contains dams in the High Hazard category. The flood warning system was developed using Hydstra Modelling™ (formerly TimeStudio), which links directly to the Hydstra TSM™ database. This package offers powerful automation tools that enable the Pieman River flood warning system to operate, alert personnel and display results on Hydro Tasmania’s internal website with no manual involvement. With its maintenance free operation and user-friendly interfaces, the Pieman River flood warning system is an effective contribution towards the overall risk management package of the Pieman River Power Development
SEQWater is the major supplier of untreated water in bulk to Local Governments and industry in the South East Queensland region of Australia, through ownership of Wivenhoe, Somerset and North Pine Dams. Wivenhoe Dam (Lake Wivenhoe) is located on the Brisbane River in Esk Shire. The storage provides both flood mitigation and water supply storage to Brisbane and Ipswich. The water supply storage capacity at full supply level is 1,160 GL. An additional 1,450 GL of storage above full supply level is used for flood mitigation.
Changes to the estimation of extreme rainfall events has resulted in significant increases in the estimates of the PMF since the original design of Wivenhoe Dam. To upgrade the flood security of Wivenhoe Dam, SEQWater has formed an alliance with Leighton Contractors, Coffey Geosciences, MWH and the NSW Department of Commerce.
This paper details the alliance delivery method, the latest estimates of the PMF based on the GTSMR method and details of the two preferred options being finalised by the Alliance.
This paper discusses reliability issues of the fourteen 3.85m high by 7.89m wide radial gates at Glenmaggie Dam in Victoria and the twin 3.6m high by 16.5m wide drum gates at Little Nerang Dam in Queensland. The Glenmaggie dam radial gates are manually controlled using electrically driven (mains and diesel generator power supply) hoist motors with a petrol driven hydraulic pack for use in the event of complete electrical power supply failure. A detailed fault tree analysis was developed for the spillway gate reliability of the Glenmaggie Dam gates as part of the risk assessment for the dam, which was being completed at the time of publishing the paper. Each of the identified components of the spillway gates, including human error in operation was used to evaluate the probability of failure of a single gate or multiple gates for inclusion in the event tree to estimate the risk and assist the evaluation of the requirement for remedial works. The Little Nerang drum gates are fully automatic hydraulically operated gates with independent operating mechanics and a common override system in the event of automatic system failure. Drum gates are uncommon on dams and the system operation is discussed together with an assessment of the reliability and measures taken for handling operating risks during floods for the dam, which has some stability concerns.
Cold water pollution occurs downstream of many Australian dams when water is released from well below the surface layer of a stratified reservoir during spring and summer. Water temperature can be depressed by 8 °C or more and this may impact negatively upon the survival and growth of native Australian fishes.
After many years in the ‘too hard basket’, mitigation of cold water pollution below dams is receiving increasing attention in Australia. Hume Dam is a case in point. Hume Reservoir, one of the largest irrigation reservoirs in Australia, has a high throughput of water (short residence time) and receives unseasonably cold water from Dartmouth Dam on the Mitta Mitta River and the Snowy Mountains Hydro Scheme on the Murray River.
The maximum possible discharge temperature below Hume Dam may be constrained by geomorphic and climatic features beyond human control. Specifically, the relatively short residence time of water may limit the extent to which it can heat up in the reservoir prior to discharge downstream. Here I present a heat budget for Lake Hume and address the question, “How much can we improve the thermal regime below Hume Dam.”
Garth Barnbaum and Robert Bell
Hydro Tasmania has recently upgraded the control systems for the spillway gates of three of its dams, Clark Dam, Meadowbank Dam and Liapootah Dam. The upgrades followed internal reliability assessments that highlighted high reliance on operator attendance, single points of failure and operational difficulties on each of the three gate systems.
The three gates are of contrasting types. Clark Dam Spillway Gates are submerged orifice type radial gates, operated by wire rope hoists. Meadowbank Crest Gates are flap type gates, held by 10 hydraulic cylinders per gate, a design that has had a difficult operating history. Liapootah is a floating drum gate. The upgrades for each gate therefore required different solutions, albeit within a common basis of design framework. The solutions arrived at are innovative, and meet or exceed worlds best practice.
All three gates are now fully automatic, with PLC control. The use of PLC’s significantly enhances the reliability of the gates. Extensive use is also made of the PLC in monitoring key systems. For example, an impossibly rapid lake level rise detected by one transducer, but not its duplicate, will be alarmed but ignored to avoid unnecessary discharge. All systems incorporate appropriate redundancy. The PLC systems also provide some automatic functional testing functionality and enhance remote alarms and local fault finding.
Mechanical systems were modified to facilitate automation and increase reliability. Stand by power sources used include auto-start diesel genset, DC batteries and a micro hydro generator.
The design and implementation of each of the upgrades was carried out by the Electrical and Mechanical Group of Hydro Tasmania’s Consulting Division, in conjunction with Generation Division’s Project Management Group.
The paper highlights the fundamental importance of correct data selection and storage for the quality of Asset Management demanded for today’s water industry infrastructure.
In developing this theme, the concept of Risk driven maintenance is introduced to focus attention on those issues that not only the identify the appropriate data to be collected and stored, but also, by way of illustrated examples, the direct relevance and application of reliability engineering principles in Risk Analysis.
The author’s principle objective is to demonstrate that the historical data on reliability, condition and performance must be supported with detailed costing information if any worthwhile outcomes are to be forthcoming from analysis.