Dam safety emergency plans (DSEPs) are typically produced for individual dams. For owners of a large portfolio of dams, this approach creates document control difficulties, requires excessive time and effort and can lead to confusion when a single emergency affects multiple dams having individual DSEPs. Hydro Tasmania has developed a single DSEP which is applicable to its portfolio of 54 referable dams. The DSEP contains generic emergency response procedures, is applicable to a whole range of generic dam safety incidents, uses a simple colour-coded flowchart-action list format, has a two-stage emergency response, retains all necessary dam-specific information and can be easily adapted to any organisational structure. This approach was found to have benefits in document control, flexibility in the management of the emergency response and short lead time in terms of having DSEPs which cover an entire portfolio of dams.
Many dam structures in Australia were designed and built in the 1950s and 60s with limited hydrological information. As a result existing spillway structures are under-sized for today’s revised probable maximum floods (PMF). Potential problems such as the generation of excessive negative pressure over spillway crest under increased flood condition could be encountered. This may cause instability or cavitation damage to the spillway. The raised flow profile may also have adverse impacts on crest bridges and gate structures.
Historically, physical models have been constructed in hydraulic laboratories to study these behaviours, but they are expensive, time-consuming and there are many difficulties associated with scaling effects. Today, with the use of high-performance computers and more efficient computational fluid dynamics (CFD) codes, the behaviour of hydraulic structures can be investigated numerically in reasonable time and expense.
This paper describes the two- and three-dimensional CFD modelling of spillway behaviour under rising flood levels. The results have been validated against published data and good agreement was obtained. The technique has been applied to investigate several spillway structures in Australia.
J.H. Green, D.J. Walland, N. Nandakumar
The Bureau of Meteorology has recently revised the Probable Maximum Precipitation (PMP) estimates for the Generalised Tropical Storm Method (GTSM) region of Australia. The revision process has involved the application of the more technically rigorous Generalised Southeast Australia Method (GSAM) that was previously developed for the southern part of Australia to a much larger data set of severe tropical storms. This has generally lead to an increase in the total GTSM PMP depths with a resultant increase in the Probable Maximum Precipitation Design Flood (PMPDF) and the Probable Maximum Flood (PMF).
In addition, the revision process has produced significant modifications to the temporal and spatial patterns adopted when applying the PMP depths to a dam’s catchment and these changes have also generally lead to increases in the resultant floods.
This paper discusses the rationale behind the increases in PMP depths and changes in the associated temporal and spatial patterns and presents the justification for the adoption of these more scientifically defensible estimates.
The application of the revised PMP estimates to the Keepit Dam catchment in northern NSW is presented and a comparison between the PMPDF and PMF estimates based on the original GTSM and the revised GTSM (GTSMR) made for this specific case study.
This paper presents the findings of experimental investigation of internal erosion by the process of suffusion within embankment dams and their foundations.
Suffusion is the process by which finer soil particles are moved through constrictions between larger soil particles by seepage forces. Soils susceptible to suffusion are usually described as internally unstable. Understanding of the suffusion process is important to the assessment of the risk of internal erosion in an embankment dam and its foundation. Suffusion results in a coarser soil structure, leading to increased seepage, progressive deterioration of the dam or its foundation, and a higher risk of toe instability. Suffusion within the protective filter of a dam may result in a coarser filter, rendering it ineffective in protecting the core materials from erosion.
Two types of suffusion tests, namely the downflow test and the upflow test, have been conducted at the University of New South Wales. The downflow test aims at identifying the types of soils that are susceptible to suffusion, whereas the upflow test aims at identifying the hydraulic gradient at which suffusion is initiated. This paper presents the initial findings of the downflow test. Eighteen downflow tests have been carried out on fourteen clay-silt-sand-gravel soils. The Kenney and Lau (1985, 86) method, which is commonly used for assessing the internal stability of coarse-grained soils, appears to be too conservative when used to predict the internal stability of silt-sand-gravel or clay-silt-sand- gravel soils, whereas the Burenkova (1993) method appears to provide better predictions. Further testing is required to define more accurate criteria for determining the internal stability of broadly-graded clay-silt-sand-gravel soils.
There is a widespread perception among dam engineers that tree root invasion occasions a very serious threat to embankment dams by virtue of its potential to initiate piping failure, with appropriate action invariably recommended. Remedial works can, on occasions, be extensive.
While the principle is ostensibly plausible and scarcely challenged, there has never been, to the Author’s knowledge, a satisfactory investigation to establish any credible scientific basis for it. One case that has attracted some attention in literature (by virtue of the extent of the investigation undertaken), viz a piping accident at Yan Yean Dam, is critically reviewed to show that the accepted view on the role of tree roots in this incident is less than satisfactory. In the course of this review, two physical Laws of Piping are proposed, and applied both to this case and to another nearby Melbourne Water dam that also has a history of piping.
Whilst the consequences of piping in a major dam are such that risk from this source must be kept to a very low level, it is concluded here that piping risk arising from tree root invasion has been considerably overstated and that a more balanced assessment is necessary before determining what, if any, action is required.
The RCC design review and construction supervision of the 60m high Tannur Dam in Jordan was carried out by GHD, Australia.
The 220,000m3 of RCC was placed during February-December 2000; change to the sloped layer method was made once the dam reached 15m height. It produced a 50% increase in placing rate and a considerable saving in costs.
The use of the method is the first known use outside of China, where it was developed during the construction of the 130m high Jiangya Dam in 1997-8. The sloping of the 300mm thick layers of RCC across the dam from bank to bank at grades between 5-8% ensures subsequent layers of RCC can be placed within the initial set time of the lower layer and hence the RCC is monolithic across the lift joint.
This paper briefly describes the project in Jordan and then gives specific details of the use of the sloped layer method. Typical results from the quality control testing during placement and subsequent coring and testing of the lift joints are also provided. The benefits of its use in adverse climatic conditions, such as extreme heat or rainfall and the ways it can be integrated with forming the upstream-downstream slope are also discussed.
The sloped layer method is a significant advancement, particularly for large structures, where lift joint cohesion, tensile resistance and RCC placing rates are vitally important.